Phantom-tech Projector User Manual

Browse online or download User Manual for Projectors Phantom-tech Projector. Phantom Tech Projector User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 2
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
ILLUMINATIONS
607 Durham Drive
Houston, Texas 77007-5316
Tel: 713-863-1133 / Fax: 713-863-0044
TA SERIES
TOP-ACCESS
INSTRUCTION SHEET
Lighting Design
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To ensure full compliance with local
codes and regulations, check with your local electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box
before proceeding. Retain these instructions for maintenance reference. TECHINCAL SUPPORT (800) 863-1184 8am-4pm CDT M-F
INSTALLATION PROCEDURE FOR PHANTOM TOP–ACCESS FIXTURE
REMOVE THE FIXTURE AND MOUNTING HARDWARE FROM THE CARTON. IDENTIFY ALL PARTS AND READ THE FOLLOWING
ASSEMBLY INSTRUCTIONS BEFORE PROCEEDING WITH THE INSTALLATION. THE INSTRUCTIONS ARE IN A STEP BY STEP SEQUENCE
FOR CORRECT AND EASY ASSEMBLY. PLEASE FOLLOW THE SEQUENCE! SAVE THE CARTON AND ALL PACKING MATERIALS UNTIL
JOB IS COMPLETE. SAVE THESE INSTRUCTIONS FOR MAINTENANCE REFERENCE! U.S.. PATENT PENDING
2. DETERMINE MOUNTING LOCATION
Once you have determined the best location for the projector,
go into the attic to see if you have the area necessary to install
the housing. Using a Philips head screwdriver make a hole in
the best location for the projector trim. After making your hole
go to the floor below and check to see if it is in the correct
location. Keep the hole that you made with the screwdriver in
the center of the elongated hole in the heat shield. Adjust the
housing forward or backward as needed. The mounting arms
are turned inwards for shipping purposes, rotate the arms to
the outward position so that you will have a better drilling
position for your mounting screws. Extend the mounting arms
to fit snuggly between joists and screw into place. Tighten the
three hex head screws to anchor the arms and secure to
housing.
Using the heat shield and a key hole saw, cut around edge of
appropriate knock out hole as clean as possible. Elongated
hole is for angle aiming and the center hole is for vertical
aiming. It is OK if the housing and projector are not centered
on painting. The projector works perfectly at angles off center
of art. For vertical appplications no trim is provided.
C
US
R
73355
(3) Black Knobs
(2) Condensing Lenses
(3) Focal Lenses
(1) Projector
(1) Junction Box
(3) Sets of Shutters
1. COMPONENTS CHECK LIST
(1) Glare shield
(1) Breakaway Cone
(1) Housing
(1) Heat shield
(1) Custom Trim
(1) (Optional) Slide
(1) MR 16 Lamp (EYC)
(1) Projector Supplement
ETL LISTED, LUMINAIRES TO UL STD 1598
& TRACK LIGHTING TO UL STD 1574
A projector supplement has been provided to illustrate projector
performance, location and beam configurations. Determine the
exact location and verify adequate space between rafters and
depth of ceiling cavity to accommodate housing before
proceeding. Because this a custom installation a second person
might be required to assist in the application.
(1) Mounting Cradle
(1) Rotating Ring
4. CUT OPENING FOR CUSTOM TRIM
Art
Joist
Joist
Heat Shield
12"
12"
9"
3. INSTALL HOUSING / ATTIC ACCESS ONLY
(1) Allen Wrench
Page view 0
1 2

Summary of Contents

Page 1 - TA SERIES

ILLUMINATIONS607 Durham DriveHouston, Texas 77007-5316Tel: 713-863-1133 / Fax: 713-863-0044TA SERIESTOP-ACCESSINSTRUCTION SHEETLighting DesignREAD AND

Page 2

ILLUMINATIONS607 Durham DriveHouston, Texas 77007-5316Tel: 713-863-1133 / Fax: 713-863-0044TA SERIESTOP-ACCESSINSTRUCTION SHEETLighting DesignLAMPING

Comments to this Manuals

No comments